CCTV cameras are available with various voltage
requirements. These include 12VDC, 24VAC, and 115/230VAC. 115/230V models are
rarely used, due to the expense of providing local high-voltage power. 24VAC
models are quite common in that they can tolerate greater wire distances than
their 12VDC counterparts, and are generally more immune to ground-loops. A
significant portion of cameras today are wide-ranging in that they can operate
on 12VDC or 24VAC.
12VDC Operation
Should the camera operate off of 12VDC only, special considerations must be taken to ensure correct operating voltage. These considerations include short wire runs, thick wire gauge, or slightly increasing the power supply voltage to achieve the correct voltage at the camera. Another consideration is that 12VDC cameras often connect the power supply return lead to the camera’s ground. The result can be that current from the power supply may flow through the shield of the video path, a recipe for ground-loops. For this reason, it is recommended that 12VDC cameras be powered from a local 12VDC supply that has a floating (not grounded) output.
Some products that allow 4-pair UTP wire to be used to deliver camera Power, Video, and if necessary, telemetry Data. Some “cable integrator” pass-through devices that allow the use of an external power supply and RJ45 connectorisation for in-house wiring. This allows for inter-operability with external low voltage power supplies, including those that deliver 12VDC. An example might be a 4 watt 12VDC camera, which is limited to a wire distance of 43ft (13 meters). This is not a particularly impressive distance, but a better solution is listed below after we discuss 24VAC operation.
24VAC Operation
Also in the UTP range are cable integrators that have built-in individually floating 24 or 28 VAC power supplies. The 28 Volt setting allows 24VAC cameras to operate at extended distances over 4-pair UTP wire. Here, a 4 Watt 24VAC camera with a ±10% tolerance can operate up to 1,047ft (319m).
Dual Voltage 24VAC/12VDC Operation
Many 24VAC and 12VDC cameras are specified to be powered from a source that is ±10%, which is a range of 21.6 VAC to 26.4 VAC or 10.8 VDC to 13.2VDC, respectively. To reduce the number of camera models, most camera manufacturers incorporate a switching power supply that will operate comfortably off any voltage from 10.8 to 30 volts AC or DC. These wide-ranging switchers can therefore operate off 24VAC or 28VAC at very long wire distances, allowing cameras to be powered from the head-end control room. This allows for the entire system to operate off of one UPS. Here, a 4 Watt camera can operate off a 28VAC supply but tolerate a voltage of 14 VAC, yielding 1,467 feet (447 meters). A 2.75 Watt camera can go over 2,000ft (600m).
12VDC Cameras Powered from a 24VAC Supply Should the camera not operate over this wide range, consider using Converter the camera to convert from 24VAC to 12VDC. Easily operate off a voltage as low as 12VAC, allowing it to be powered from a 24VAC or 28VAC source. When calculating distance, set the Camera Minimum Voltage parameter to 14V (half the 28VAC value is where we get maximum power transfer), and set the Camera Power parameter to be 10% higher than the camera’s published rating. The camera current should not exceed 400mA. A 4 Watt 12VDC camera can be 1,336ft (407m) away from the power supply. a 2.75 W 12VDC camera can be 1,942ft (592m).
If you are design analog based CCTV projects, consider per camera per power supply. Always power cameras from a local power source such as a small transformer / SMPS. This is a simple way to do it and will require less cable having to be run which may be fine in a small / Big installation. Do not used Multi-Camera power supply, sometimes called a PDU (power distribution unit) to provide power for the cameras.
As an example a camera my show 5W at 24 VAC. How many amps is that? Based on the chart you would divide 5 by 24 for approximately 0.200 amps or 200 mA (milliamps).
If you have 4A Power Supply then see what happend as in below exp:
Also Visit: http://arindamcctvaccesscontrol.blogspot.in/2012/11/voltage-amperage-guide-for-your-cctv.html
12VDC Operation
Should the camera operate off of 12VDC only, special considerations must be taken to ensure correct operating voltage. These considerations include short wire runs, thick wire gauge, or slightly increasing the power supply voltage to achieve the correct voltage at the camera. Another consideration is that 12VDC cameras often connect the power supply return lead to the camera’s ground. The result can be that current from the power supply may flow through the shield of the video path, a recipe for ground-loops. For this reason, it is recommended that 12VDC cameras be powered from a local 12VDC supply that has a floating (not grounded) output.
Some products that allow 4-pair UTP wire to be used to deliver camera Power, Video, and if necessary, telemetry Data. Some “cable integrator” pass-through devices that allow the use of an external power supply and RJ45 connectorisation for in-house wiring. This allows for inter-operability with external low voltage power supplies, including those that deliver 12VDC. An example might be a 4 watt 12VDC camera, which is limited to a wire distance of 43ft (13 meters). This is not a particularly impressive distance, but a better solution is listed below after we discuss 24VAC operation.
24VAC Operation
Also in the UTP range are cable integrators that have built-in individually floating 24 or 28 VAC power supplies. The 28 Volt setting allows 24VAC cameras to operate at extended distances over 4-pair UTP wire. Here, a 4 Watt 24VAC camera with a ±10% tolerance can operate up to 1,047ft (319m).
Dual Voltage 24VAC/12VDC Operation
Many 24VAC and 12VDC cameras are specified to be powered from a source that is ±10%, which is a range of 21.6 VAC to 26.4 VAC or 10.8 VDC to 13.2VDC, respectively. To reduce the number of camera models, most camera manufacturers incorporate a switching power supply that will operate comfortably off any voltage from 10.8 to 30 volts AC or DC. These wide-ranging switchers can therefore operate off 24VAC or 28VAC at very long wire distances, allowing cameras to be powered from the head-end control room. This allows for the entire system to operate off of one UPS. Here, a 4 Watt camera can operate off a 28VAC supply but tolerate a voltage of 14 VAC, yielding 1,467 feet (447 meters). A 2.75 Watt camera can go over 2,000ft (600m).
12VDC Cameras Powered from a 24VAC Supply Should the camera not operate over this wide range, consider using Converter the camera to convert from 24VAC to 12VDC. Easily operate off a voltage as low as 12VAC, allowing it to be powered from a 24VAC or 28VAC source. When calculating distance, set the Camera Minimum Voltage parameter to 14V (half the 28VAC value is where we get maximum power transfer), and set the Camera Power parameter to be 10% higher than the camera’s published rating. The camera current should not exceed 400mA. A 4 Watt 12VDC camera can be 1,336ft (407m) away from the power supply. a 2.75 W 12VDC camera can be 1,942ft (592m).
If you are design analog based CCTV projects, consider per camera per power supply. Always power cameras from a local power source such as a small transformer / SMPS. This is a simple way to do it and will require less cable having to be run which may be fine in a small / Big installation. Do not used Multi-Camera power supply, sometimes called a PDU (power distribution unit) to provide power for the cameras.
So how do you determine the correct CCTV power supply for your security camera system?
There are two main selection criteria.
- The number of cameras to be powered.
- The total current draw.
As an example a camera my show 5W at 24 VAC. How many amps is that? Based on the chart you would divide 5 by 24 for approximately 0.200 amps or 200 mA (milliamps).
If you have 4A Power Supply then see what happend as in below exp:
Example 1: You have 2 domes drawing 1 Amp each and 6 cameras, drawing 150mA each. Your total current draw is 2.9 Amps, well within the total available current of 4 Amps. This is OK.
Example 2: You have 5 domes, drawing 1 Amp each and 3 cameras, drawing 150 mA each. Your total current draw is 5.45 Amps, exceeding the total available current of 4 Amps. This in not OK. Your installation will not work.
Practically Major Camera showing Video Loss due to use of multi camera power supply (8 in 1, 4 in 1, etc) in India. Maximum Indian (Mainly Stores, Hospital, Small Office, Hotels etc) used multi camera power supply due to low price (In 2012 you can get 12V@5A Power supply Rs. 1200/-). Where as Power Plant, Big Organization etc used 12V@1A power supply per camera (In 2012 you can get it Rs. 300.00/-) Just Imagine if you have more then 08 nos of camera.Also Visit: http://arindamcctvaccesscontrol.blogspot.in/2012/11/voltage-amperage-guide-for-your-cctv.html
12 comments:
The role of IP in deployment of power supplies
The security industry's transition to networked systems using Internet Protocol has created a paradigm shift in the design and deployment of power supplies. Today, many IP system components are powered using 15 watts of power that travel over the same cable which connects to the network using power over Ethernet (PoE) technology. Network switches may include integrated power supplies that provide PoE and the use of a mid-span power injector will ensure there is ample power. Some PoE switches may not provide PoE+ (IEEE802.3AT) which is specified for certain devices that require higher power. Mid-spans are available that provide both PoE and PoE+ injecting mid-span power onto a network cable maintaining power to the device even in case of a network outage; for example, a network camera capable of recording to an onboard SD card would continue to operate and record locally even if the network connection is out.
Power supplies are a vital component of a security system but are not always considered to be mission critical. Often situated in a utility area, power supplies are essential to a continuous, trouble-free operation. Both end users and integrators require systems that will provide 24/7 security, as well as the best return on investment (ROI). The last thing any systems integrator or end user wants is to deal with costly service calls as a result of unreliable products or a flawed system design.
A variety of power supply options are available in many configurations. Selecting the correct power solutions matched to specific products and their locations ensures trouble-free operation and adds a high degree of reliability
Every Security Surveillance System requires some form of power supply for the cameras. Some CCTV Cameras use AC Power, some use DC Power, while there are some that are Dual Voltage. This means that they will accept both AC and DC Power. It is important to take note of the power requirements of your Security Cameras when choosing your CCTV Power Supply. Security Camera Power Supplies come in 4, 8, 9, and 16 channel versions as well as AC and DC Voltages. So, depending on the voltage requirements of your Surveillance System, you may need to mix and match your power supplies to meet your individual needs.
Thanks for sharing CCTV bus solutions in dubai
THANKS FOR SHARING SUCH A AMAZING WORK
GREAT PIECE OF WORK!!!
cctv suppliers in dubai
Thank you for the information people counting solution
Thanks for sharing Home Security Cameras Installation
Good content turnstile gates dubai
This articles about 'Power consideration of IP camera' was very helpful. Most of the people do not know about this.
Thanks
Camera Vision
It is really a helpful blog to find some different source to add my knowledge. Camera Installation Near Me
These Lock Systems Replacement Parts the traditional keys with better and more secure automation features like remote locking and unlocking. In these locks, a latch or bolt is made to cross the opening between the side of the door and the doorframe, thereby preventing access.Digital Door Locks,also known as keyless doors, the locks replace the keys with a digital screen, where you can put numeric digits as a code.
Thanks for the amazing and detailed information.
Click here to know more CCTV Camera SMPS
Post a Comment