How to add a microphone to an IP Camera

How to add a microphone to an IP Camera

Most security cameras that are outdoor rated do not come with built-in microphones to ensure that no water can leak in. This means that you must add an external security camera microphone to these cameras in order to record audio. CCTV Camera World carries microphones for indoor or outdoor cameras. Most IP security cameras with audio input capabilities have an RCA audio connector on their pigtail for connecting a microphone. Some dome IP cameras have a connection block on the inside of the dome. In either case, physically connecting and configuring external microphones to an IP security camera is easy as shown in this guide.

How to tell which camera you have?

In case you are unsure, here's a quick image to help you understand which type of audio connection your IP camera has.

Depending on whether your camera has a RCA or two-wire line in connection, please follow the appropriate section below.

1.   Connecting a microphone using RCA input

2.   Connecting a microphone using two-lead wire

3.   Enabling audio-input on the camera

 

 

 

Setup for IP Cameras with RCA Audio Input connectors

What's needed?

Here is what you need to connect a microphone to an IP camera that has RCA audio inputs:

1. Outdoor Microphone (sku 71891) or Indoor Microphone (sku 7100CC)
2. 12V DC 500mA Power Supply (sku 12V5MA)
   You can also use PoE Power Splitter (sku POE101D) with DC Power Splitter Cable (sku DC-PJJ)
3. RCA Male to RCA Male Adapter (sku RCA01)

How to connect a microphone to an IP camera that has RCA audio input

Below is a diagram of how to connect an external microphone to the RCA audio connector on an IP camera.

It is easy to connect a mic by following these easy to follow steps:

1. Connect the microphone to the RCA audio input on the camera's pigtail using a RCA Male to RCA Male connector
2. For longer runs between the camera and microphone you can use an RCA cable with male ends to connect the input and output.
3. Connect the power connector from the 12V DC Power Supply to the female power jack on the microphone.

Alternatively, you can also use a PoE Power Splitter with a 1-to-2 DC Power Splitter to use PoE power for the microphone and camera. Simply connect the PoE cable into the PoE splitter. Then split the power to the camera and microphone using the DC splitter. The data cable for the PoE splitter then connects to the camera for data.

After you have correctly wired the microphone to the camera you can continue to the rest of the article to find out how to enable the cameras audio input for listening and recording.

Setup for IP Cameras with Audio Line-in Input

Some IP security cameras include an internal audio line-in block or a two-wire lead that requires a two-lead connection for connecting a microphone. At first it may seem puzzling how a microphone with a RCA connection would connect to a two-wire input. As an example, in the section below we use a video balun, BNC to RCA connector, and two-lead wire to connect the microphone to the line-in block.

What's needed?

You will need the following items to connect a microphone to a camera with a line-in audio connection consisting of two-lead cabling.

1.   Outdoor Microphone - (sku 71891) or Indoor Microphone (sku 7100CC)

2.   12V DC 500mA Power Supply (sku 12V5MA)
You can also use PoE Power Splitter (sku POE101D) with DC Power Splitter Cable (sku DC-PJJ)

3.   Video Balun (sku VB2PHD)

4.   BNC Female to RCA Male Connector (sku BNCRCA02)

5.   Two-lead Wire for the balun

Best Practices for Using A Two-Way Audio Security Camera

Whether you have a security camera system for a home or business, the need for two-way audio interaction with talk-back capability may arise. CCTV Camera World offers solutions for both one-way and two-way audio. One-way audio is great for listening to sound originating from the location of a camera, but it will not allow interaction with a person at that location. To be able to interact with a person at the camera, the camera would have to have two-way talk capabilities, i.e. a speaker and microphone built-in similar to an intercom.

Two-Way Audio Setup With PoE NVR

Step 1) Connect cameras to NVR

In this guide, we will be using our security camera with two-way audio, sku IP3MPA.  It is a two-way audio IP camera that allows the user to not only listen-in, but also talk back to the person at the camera. These cameras are very easy to connect using the plug-and-play technology. In the video demonstration above we show how easy it is to connect our PoE IP cameras to our PoE NVRs. Simply connect the cables between the camera and the NVR. A single network cable transmits power and data to each camera from the NVR, and plug-and-play technology handles IP address configuration between the camera and NVR without user intervention.

Using a Web Browser for Two-Way Audio

Our camera systems allow the user to engage in two-way talk over the network by using Internet Explorer on a computer or by using our iOS and Android apps for both phones and tablets. First, we will demonstrate how to use the web portal called Web Service in our security systems. A Windows PC running Internet Explorer is required for two-way talk capability through the web browser. To be able to talk-back, you will need to make sure you have a headset or combination of microphone and speaker on your PC to listen and talk-back.

All DVRs and NVRs from CCTV Camera World are network devices and have their own IP address. You first need to connect your security camera system to your network by assigning the DVR/NVR an IP address that fits your network scheme. Once that is complete, you will be able to view your system from a computer or smartphone and use the two-way audio feature over the network. If you wish to view the system over the web when away from home, you will need to set port forwarding rules on your router's firewall to allow remote viewing from the internet.

Once your system is properly connected to your network and port forwarding rules have been created on your firewall, you will be able to engage in two-way audio communication using your smartphone, tablet, or PC from anywhere in the world where Internet is available.

Step 2) How to use two-way talk on Internet Explorer

1.   Open an Internet Explorer window on your Windows PC and type in either your NVR's IP address for local viewing, or external IP address for remote viewing.

2.   Type in your system's username and password, and select Login.

3.   Make sure audio is enabled in your two-way camera by going to Setup and Encode.

4.   Click the Audio Enable check boxes for both the Main and Sub Streams (if they are not already checked).

5.   Select OK to ensure your settings have been saved.

6.   Click the Preview tab to view your camera's live feed.

7.   Select the channel by clicking the quadrant containing the video feed. A green frame will appear around the video feed to distinguish the selected channel.

8.   Select the Speaker Icon in the top-right corner of the selected camera's video feed for one-way audio. This will allow you to hear audio that's taking place at the location of your camera.

9.   To talk back and send out audio through the camera's speaker, select the Microphone Icon in the top-right corner of the selected camera's video feed. You will need either a headset with microphone, or a combination of microphone and computer speakers to listen and talk back.

Now you will be able to listen and talk back to someone at the location of your camera. Note that you will be able to listen to camera audio feeds one at a time - you will not be able to listen to multiple audio feeds simultaneously. Multiple users can listen to one-way audio from a camera, but the talk back function is done by one user at a time.

If a computer is not available to view your two-way audio camera system, then proceed to the next section where we explain how to use two-way talk with a smartphone or tablet.

Two-Way Audio Interaction Using iOS or Android Phone/Tablet

A more convenient way of viewing you security camera system and engaging in two-way audio talk is through your mobile device. The App allows the user to hear incoming audio from the camera and uses the microphone from the phone to talk back, sending out audio through the camera's speaker.

Step 3) How to use Two-Way Talk with a Smartphone or Tablet

1.   First, Open the app (iDMSS) on your iPhone or Tablet (or gDMSS for Android devices).

2.   Select the Menu Icon in the top-left corner, and choose Device Manager.

3.   From here, select the Plus Sign in the top right corner,  Wired Device and then IP/Domain.

4.   Fill out the appropriate credentials of your NVR. You will need to create two entries - one for viewing at the location of your system using Wi-Fi, and second entry for when viewing remotely over the internet away from home. We have a tutorial on how to create entries for both local and remote viewing. After all credentials have been entered, select Start Live Preview.

5.   Select the camera channel you want to engage in two-way audio with by tapping the video feed from that camera, and then press the Speaker Icon. The speaker icon allows the user to  listen to incoming audio from the camera and talk-back sending out audio through the camera's speaker.

Briefly, here is what we did:

1.   Open the dome cover of the camera using the included hex-key tool. Do not use powered screwdrivers or drills or you will damage the dome.

2.   Connect the BNC Female to RCA Male connector to the balun.

3.   Connect the RCA Male tip to the RCA input on the microphone.

4.   Use the video balun to wire in the two lead wire, tighten the screw-downs for the wires.

1. Make sure that you remember the polarity for your wires. We suggest using Red for the positive wire, and Black/Striped for the ground/negative wire.
2. Having a bad connection or the wrong polarity will not record sound or have loud interference.

5.   Locate the small rubber insert next to the Audio/Alarm block and create a small hole for the wires.

6.   Slightly unscrew the screw-down for the Audio-In connector on the block. Insert the positive wire from the video balun and screw it down.

7.   Slightly unscrew the screw-down for the ground connector (GND). Insert the ground wire from the video balun and screw it down.

8.   Run the power cable for the microphone to the 12V DC power supply that is connected to a 220V AC power outlet. Connect the power supply to the microphone.

a)   Alternatively you can use a PoE splitter with a 1-to-2 DC power splitter.

b)   Connect the PoE cable for the camera to the PoE splitter. Then connect the PoE splitter to the 1-to-2 DC power splitter.

c)   Connect the camera and microphone to the DC power splitter connectors.

d)   Connect the RJ45 jack coming from the PoE splitter into the pigtail on the camera.

Once you finally have your camera and microphone connected you can continue to follow the rest of this guide to learn how to enable audio input on the camera.

How to enable audio recording on an IP camera

After everything is connected you must configure the camera to recognize and use the external microphone. This step is extremely important before trying to listen and record a camera. Do not assume that the camera is automatically recording audio when you plug the microphone in.

Using Internet Explorer to enable and modify audio settings

In the video below we show how to use Internet Explorer to login and modify the settings on an IP camera. This process requires knowing what the IP address of the camera is. After that it is as easy as logging in and going to the Settings page. Navigate to the Camera > Audio page. There you will find the audio settings for the camera. You can enable audio for Main-stream or Sub-stream, fine tune the volume settings, and enable the noise filter. Also if a camera has a built-in microphone you can set it to use the external microphone instead.

Step by Step Guide to Remote view DVR

CCTV – Guide to Remote view of DVR

This post will walk you through setting up a CCTV DVR for remote viewing on Mobile or PC.

Connect the cameras to your DVR using BNC connectors & provide the power supply to DVR.Connect a mouse to the USB port. To view the cameras the DVR can be connected to a monitor through the VGA output of DVR or to a TV through the Video out pin (you may need a BNC to RCA converter)

Connect the DVR to the Network Router (providing internet connection as well as LAN) using the RJ45 Ethernet cable. 

For this demo I’m using DVR, Camera & a Linksys Router.

Right click on DVR screen to get the Menu list.

Click on Home & then click on Network tab.

For Net Link there are two options. Static IP & DHCP.

If you select Static IP, you’ve to feed the IP address manually.

DHCP is Dynamic Host Configuration Protocol. Generally a Router is at the top of a Network & it assigns IP address to a device like DVR when connected to it.

Select this option DHCP.

Note down the IP Addresses.

Here the IP address of DVR is assigned as 192.168.1.108 & the Gateway address is 192.168.1.1 .

The Gateway address is the IP address of the Router.

To view DVR over Internet or Mobile you’ve to open two ports for the incoming traffic on your Router.

1) HTTP PORT &

2) MOBILE PORT.

At the bottom you can see HTTP port assigned as 80.This is the default port for webservice WWW.

Click on the arrow mark next to Netservice to know the Mobile port number.

Here the Mobile port number is shown as Mobile Monitor & port assigned is 34599

Now we shall see how to open these two ports 80 (HTTP) & 34599 (Mobile)  inside Router’s settings.

This process is called Port Forwarding.

PORT FORWARDING SETUP ON ROUTER.

Open a web browser like Internet Explorer or Firefox.Type in the Gateway IP address 192.168.1.1

Following table is a list of some Routers with IP address, Username & password.

In this demo we’re using a LinkSys Router.  So type in the IP 192.168.1.1

User Name is admin & password is also admin

Setup Window of Router opens.

You can note that the Router IP address as well as Network IP address are displayed.

Click on Application & Gaming tab.

Click on Port Range Forwarding tab.

Enter any name  under application , say , DVR . Under start , as well as End enter the HTTP port 80.

Select Protocol as Both. Under IP address enter the IP of DVR. Here it is 192.168.1.108.

Check mark the Enable.

Same way enter application name as DVR1 for the Mobile port enabling. Under Start & End enter 34599 .Protocol is Both & IP is the address of DVR.

Save the settings.

Now it’s time to check whether the Forwarded Ports can be seen from outside over Internet.

For this open the web browser & visit  www.canyouseeme.org

This website displays your current external IP address , along with a question “What Port ?”

Enter the HTTP port 80 & click on Check port button.

You should see a “Success : I can see your service on IP xxx.xxx.x.x on port 80 “.

Again check for the mobile port 34599 to see a success.

If you do not get a success , the port forwarding you’ve done is not correct.Again open the Router Setup & check the correct entries for port forwarding.Check whether the Enable box is checked.

Once you see Success on this site , you can go ahead with your Mobile installation.

Basic Things to Know About CCTV as a Technician

Some Basic Things to Know About CCTV as a Technician, If you are manager just share this with your team.

Cable Running

Many facilities use closed circuit television (CCTV) as part of an overall security system. Cameras mounted on buildings or ceilings transmit signals to a central monitoring room. CCTV takes two forms ---hard-wired or wireless. A technician just starting out in CCTV has to gain a knowledge base of how CCTV works, so he will be able to install, test and troubleshoot systems. Do not run 3+1/4+1 CCTV Cable, use RG11, RG6, RG59 only. Find-out the length of Video Cable from DVR to Camera, it should be on limit. Do not overlapping with High voltage wire. Do not join the Video Cable, use complete length ( One drum Video Cable its 305Mtr) of wire. If cable layed in out door use Armour cable.

RG 59 which can transmit signals up to 200 metres. This distances are for a single run of cable with no amplifiers or in-line correctors.

RG 11 which can transmit signals up to 270 metres. It is more expensive because it is thicker. This distance are for a single run of cable with no amplifiers or in-line correctors.

RG 6 which can transmit signals up to 400 metres. It is more expensive because it is thicker. This distances are for a single run of cable with no amplifiers or in-line correctors.

Twisted pair cable is a good alternative to coaxial cable if the length of the run is more than a few hundred metres. With pure cooper twisted pair, runs of up to 600 metres can be used without any in-line repeaters.

Troubleshooting Signal Loss

The picture on the monitor should never be fuzzy or have interference patterns. If it does, signal loss is occurring somewhere in the system. Technicians have specialized testing equipment and know how to use them in order to troubleshoot systems. Usually, a technician starts at the camera and works her way back to the receiver. She/he checks each connection until the test equipment indicates a loss. Some common problems are corrosion due to moisture inside the connectors or cables chewed through by animals.

Camera Installation

CCTV technicians can't be afraid of heights. Cameras are mounted high on the sides of buildings, or high in the ceiling areas of stores. You have to use a boom lift to reach spots to mount cameras. If you suffer from heights, becoming a CCTV Technician may not be a valid career path.

Cables are installed from the camera to the receiver station. You will have to drill through masonry block and below floor to run the cable. Be prepared to navigate through tight cramped quarters to get the cable from the camera to the receiver. Bring along a change of clothes, since you will get dirty in the process.

CCTV Camera Installation Tips:-

1. Test all equipment before installation. Therefore equipment can be replaced before arrival on-site if needed.
2. Ensure the mounting brackets of outdoor speed domes are properly sealed to prevent condensation in the camera housing.
3. Ensure sufficient space for camera, lens and connectors when choosing camera housing.
4. Avoid direct sunlight on equipment as it raises the temperature of the equipment.
5. Position cameras out of reach of vandals or 'curious' people.
6. Mount good quality mounting brackets in a stable location to avoid unstable or vibrating images caused by vibration or wind.
7. CS Mount cameras placed inside, at industrial or dusty/damp installations should be placed into outdoor camera housings.
8. Avoid installing cameras too high above the subject thus preventing 'top-of-head' video images
9. Ensure camera mounting poles are mechanically secure to avoid vibration on camera images
10. Before connecting power, ensure the supply is 12VDC regulated.

CCTV Cabling Tips:

1. Avoid running video cable parallel to AC power cables, especially those carrying high current.

2. RG59U Coax runs should not exceed 180m for colour and 280m for B/W

3.Avoid sharp bends when cabling

4. Avoid cable joins and using BNC barrels

5. Avoid over-tightening cable-ties

6. Ensure use of proper co-ax wire-stripping and crimping tools

7. Ensure BNC Connectors are properly crimped

8. Use Rubber BNC Boots after crimping to protect crimped area and bend radius

9. Mark or label camera and data signal cables

10. Outdoor cable runs should be housed in UV-proof conduit

11. In lightning prone areas, install surge protection devices

Final Testing and Teaching

A technician tests the system after it's installed. This involves knowing how to aim the cameras, knowing how to operate the monitoring equipment in the security room and knowing how to instruct the final operators of the system. You have to be part teacher. You may have to deal with people who have no knowledge of how a CCTV system is operated, so you have to use layperson-friendly language during the training process.

As you are a Engineer / Technician remember this few points:
Visually inspect all major components and connections for signs of deterioration or damage

Check all control equipment (DVRs, VCRs, monitors, multiplexers, video switchers, telemetry units etc) for correct operation

Check mains & power supplies and stand-by batteries including charging rates.

Check environmental conditions for adverse effects, including growth or shrubbery obscuring camera views

Check time and date settings in equipment and update the settings as appropriate

Check integrity of all cabling and sample check external insulation for damage

Clean cable fixings for security

Check auxiliary lighting equipment, infra-red units and photocells (if any) for correct operation

Check air vents are clear in all control equipment including PCs

Clean cameras, lenses and housing surfaces as necessary

Check al glands and seals on external equipment

Clean control equipment surfaces including PC (if applicable)

Establish regular back-ups are taken

Check camera is aligned to user specification, pictures for correct field of view and adjust as necessary

Check brackets, towers and fixings for corrosion or damage. Check clamping bolts/brackets are tightened correctly

Check wash/wipe units and wiper blades (if any) for correct operation and fill washer reservoir where necessary

Check quality of recording during day time and night time modes

Check pan and tilt assembly (if any) including fixings, electrical connections and functions.

Check the satisfactory CCTV transmission of images to remote site (if applicable)

Check warning signs are in place

Check all camera presets

Check all alarm presets