Bit Rate

Bit Rate For DVR, NVR & IP Camera

What are Bit Rates?

Let’s start with “what is a bit, and “why do I need to know?” A bit is short for “binary digit”, the smallest unit of information in computing. It takes 8 bits to make a byte of information. “Bit rate” refers to the number of bits of data transferred in a file over a set length of time usually measured in number of “bits per second” or “bps”.

Constant bit rate (CBR) and variable bit rate (VBR) are the main types of bit rate encoding. Scene complexity can vary significantly over several hours of recorded video, and the bit rate you select for recording will have an effect on image quality, bandwidth consumption, and hard drive storage. A complex scene with moving action, such as traffic on a city street, or a scene with a lot of contrasting colors, will affect image quality and bandwidth consumption more than a less complex scene, such as an interior room with very little action or movement.

Most NVRs and IP cameras let you choose either constant or variable bit rates for recording video, and this is why you “need to know” the difference.

Constant Bit Rate (CBR)

With constant bit rate encoding, a fixed bit rate and bandwidth is used throughout the entire encoded video file. With a constant bit rate, image quality may fluctuate over the course of the video stream because some scenes are more difficult to render than others. In order for the bit rate to remain constant, the video may be encoded with fewer bits in some places or more bits in other places resulting in inconsistent image quality. Since bandwidth consumption with constant bit rates does not vary, the file size is limited and more predictable than with variable bit rates.

You will most commonly use CBR to restrict the data flow to keep network utilization as low as possible. If you have 10 cameras set to 8000K (8 megabits) on a 10/100 LAN, you are using 80% of your available bandwidth. With CBR, you can set that bit rate down to 5000K and your utilization will be around 50%.

Pre-planning your security video storage requirements is easier with constant bit rate because the amount of data being recorded never changes.

Variable Bit Rate (VBR)

With variable bit rate encoding, a changeable bit rate and bandwidth is used throughout the encoded video file. The variability of bit rates allows for video to be recorded at a lower bit rate when the  scene on screen is less complex and at a higher bit rate when the scene is more complex. Complex scenes (such as moving traffic) require more data and greater bandwidth to maintain image quality  than less complex scenes such as a wall or hallway with very little movement or action. With variable bit rates, the quality of video is higher and more consistent throughout the video stream compared to constant bit rates, yet the file size is less predictable.

Image quality is better with variable bit rates than with constant bit rates, yet pre-planning your security video storage requirements is more difficult because the bit rate changes and more complex scenes will require greater bandwidth and storage.

Here’s a Quick Look at How Constant and Variable Bit Rates Compare:

Constant Bit Rates	Variable Bit Rates
Variable video image quality	Consistent video image quality
File size is predictable because bit rate and bandwidth consumption is fixed	File size is unpredictable because bit rate and bandwidth consumption varies
Greater compatibility with most systems (compared to variable bit rate)	Less predictable compatibility (compared to constant bit rate)
When to use: When you need to limit file size and the quality of video is less important.	When to use: When consistent image quality is critical and predicting or limiting file size is less important.

The best of both worlds is when the device allows you to set VBR with a ‘Cap’ or maximum allowed bit rate.

Here is a handy ‘Quick Reference’ for setting a constant Bit Rate in bits per second.

Low Activity
Compression	Frame Rate	VGA/D1	720P/1.3MP	1080P/3MP
H.264	25~30	768K	2000K	3000K
	15~20	512K	1500K	2000K
	8~10	386K	1000K	1500K
	2~5	256K	768K	1000K
MPEG4	25~30	1000K	3000K	5000K
	15~20	768K	2000K	4000K
	8~10	512K	1500K	3000K
	2~5	386K	1000K	2000K

Normal Activity
Compression	Frame Rate	VGA/D1	720P/1.3MP	1080P/3MP
H.264	25~30	1000K	3000K	5000K
	15~20	768K	2000K	4000K
	8~10	512K	1500K	3000K
	2~5	386K	1000K	2000K
MPEG4	25~30	1500K	4000K	6000K
	15~20	1000K	3000K	5000K
	8~10	768K	2000K	4000K
	2~5	512K	1500K	3000K

High Activity or PTZ on Tour
Compression	Frame Rate	VGA/D1	720P/1.3MP	1080P/3MP
H.264	25~30	2000K	4000K	6000K
	15~20	1500K	3000K	5000K
	8~10	1000K	2000K	4000K
	2~5	768K	1500K	3000K
MPEG4	25~30	3000K	6000K	8000K
	15~20	2000K	4000K	6000K
	8~10	1500K	3000K	4000K
	2~5	1000K	2000K	3000K

In the bit rate charts above, you will see 1000K / 2000K etc. These figures can be loosely translated into ‘megabits’ per second.

1000K = 1Mb | 2000K = 2Mb and so on.

(In the computing world you would actually use 1024K = 1Mb and 2048K = 2Mb, but since most CCTV devices won’t allow those exact numbers, we just round them down to the closest thousand.) These figures are important to familiarize yourself with to manage your network load.

For example – 1 camera running a high bitrate of 8000Kbps (8Mbps) is no problem on a 10/100 network. 10 cameras at that bit rate = 80Mbps. 80Mbps is 80% network utilization on a 10/100 LAN. This is enough to see visible slowdown on the network and may begin to cause problems.

Switch to a Gigabit LAN and that becomes 8% utilization. Always check the capabilities of the network you are installing on – this can save you from a lot of headaches. When using IP cameras, always use Gigabit routers and switches when possible.  Also, make sure your NVR is connected to a gigabit switch. Plugging your NVR in to a 10/100 switch will limit your NVR to a 100Mb connection.

And finally – here is a “loose rule of thumb” for setting a bitrate:

[image width] x [image height] x [framerate] x [motion rank] x 0.07 = [desired bit rate]

Where the image width and height is expressed in pixels, and the motion rank is a number between 1 and 4. 1 being low motion, 2 being medium motion, and 4 being high motion (motion being the amount of image data that is changing between frames.).

So for instance, if we take a 1280×720 video at 24 FPS, with medium motion (movie with slow camera movements, not many scene changes…), the expected ideal bit rate would be:

1280 x 720 x 24 x 2 x 0.07 = 3,096,576 bps => approximately 3000 kbps, or 3MB

Remember – bit rates are not “universal” – different cams will give different results due to variations in encoding methods, hardware, and environmental conditions. Watch for artifacts like “ghosting” or “smearing” of moving objects.

Ghosting = when someone moving across the image may appear transparent, or may have a “ghost” following them. The “ghost” is not always transparent and may look like two people overlapped.

Smearing = when a moving object causes objects around it to change in appearance or starts to become pixilated.

Pixilated = When objects become unclear – may appear as a “smear” or slightly out of focus. In worst cases you will begin to see blocks of similar colors instead of the object itself.

RS-232 cable Wiring & Testing

COM Port (OR) RS-232 cable Wiring & Testing

As A technical background eSecurity Professional, many time got call “my Access Controller communication has RS232 enable How we connect with Computer (COM Port), is there any layout” Sometime “Successfully testing via my Laptop but Customer computer not responding, any distance or new programming is there”. I remember in year 2006 me also facing this type of problem with an Access Controller; I would be like to share the myth.

Com Port (Com1 / Com2 etc)= Serial Port = RS232 = Consol.

The wiring of RS232 has always been a problem. Originally the standard was defined for DTE (data terminal equipment) to DCE (data communication equipment connection), but soon people started to use the communication interface to connect two DTEs directly using null modem cables. No standard was defined for null modem connections with RS232 and not long after their introduction, several different wiring schemes became common. With Digital Equipment Corporation tried to define their own standard for serial interconnection of computer devices with modified modular jack connectors. This interfacing standard became available on most of their hardware, but it wasn't adopted by other computer manufacturers. Maybe because DEC used an non-standard version of the modular jack.

Very interesting is the RS232 to RJ45 wiring standard proposed by Dave Yost in 1987, based on earlier wiring schemes used at Berkeley University. He tried to define a standard comparable to DEC, where both DTEs and DCEs could be connected with one cable type. This standard was published in the Unix System Administration Handbook in 1994, and has since that moment been a wiring standard for many organizations. We will discuss this standard in detail here.

The RS-232 standard 9600bps port will drive 13 metres of shielded cable. RS232 standard is an asynchronous serial communication method. The word serial means, that the information is sent one bit at a time. Asynchronous tells us that the information is not sent in predefined time slots. RS232 sending of a data word can start on each moment. If starting at each moment is possible, this can pose some problems for the receiver to know which is the first bit to receive. To overcome this problem, each data word is started with an attention bit. This attention bit, also known as the start bit, is always identified by the space line level. Directly following the start bit, the data bits are sent. Data bits are sent with a predefined frequency, the baud rate. Both the transmitter and receiver must be programmed to use the same bit frequency. After the first bit is received, the receiver calculates at which moments the other data bits will be received. It will check the line voltage levels at those moments. With RS232, the line voltage level can have two states. The on state is also known as mark, the off state as space. No other line states are possible. When the line is idle, it is kept in the mark state. For error detecting purposes, it is possible to add an extra bit to the data word automatically. The transmitter calculates the value of the bit depending on the information sent. The receiver performs the same calculation and checks if the actual parity bit value corresponds to the calculated value. The stop bit identifying the end of a data frame can have different lengths. Actually, it is not a real bit but a minimum period of time the line must be idle (mark state) at the end of each word. On PC's this period can have three lengths: the time equal to 1, 1.5 or 2 bits. 1.5 bits is only used with data words of 5 bits length and 2 only for longer words. A stop bit length of 1 bit is possible for all data word sizes.

Goals of the Yost device wiring standard

The mess with RS232 wiring is widely known. It was the reason for starting this website. Dave Yost wanted to solve that mess once and for all, reaching as much as possible of the following goals:

1. All cable connectors should have the same connector type (RJ45)
2. All cable connectors should have the same connector gender (male)
3. DTEs and DCEs should have the same connector wiring
4. All cables should be identical (except for length)
5. No need for null modems or other special cables for specific situations

These goals are very close to the goals DEC wanted to achieve. The Yost standard has however one basic advantage. Because RJ45 connectors are used, eight pins are available which makes it possible to transfer almost all RS232 signals. Therefore the Yost standard can be used with much more equipment.

Yost DTE adapter wiring

Now we know how the cables are wired, it is time to define the adapter wiring for various equipment. Depending of the type of equipment, DB9 or DB25 connectors are used. Layouts for both connectors to a RJ45 socket for DTE equipment is shown here. The colors are defined by the Yost standard. The DTR to DSR connection is optional. Please use the manual of the device or software to decide if this loop is necessary. It doesn't harm most of the time if you connect both lines, even with systems that don't use the DSR input signal.

Test COM port by using HyperTerminal.

The HyperTerminal application has been distributed with the Windows operating system versions for a long time now, and for administrators and technical support Representatives, it can be a very useful tool. HyperTerminal allows a user to make a connection to a "host" system from a Windows computer using an available COM port. This will enable you to verify whether or not a port is active and open.  If you have never looked at HyperTerminal, take a couple of minutes to read through the following and see how it can make your life easier.

The HyperTerminal application is started by default from the Start | Programs | Accessories | Communications | HyperTerminal location. When you start HyperTerminal, you are asked to name the connection you are about to configure. This is useful as once you have configured your connection, you can then save all the settings to a configuration file of the same name. This configuration file can be used to implement equivalent settings for subsequent connections. After selecting a connection name, click OK.

On the Connect To dialog box, you are introduced to the different types of connection that HyperTerminal offers. By default, a dial-up connection using a modem is selected (assuming you have a modem present). If you have installed an external modem in addition to an internal modem that modem should also be present in the drop down menu as a choice.

 If you click the downwards arrow on the Connect Using field, you may see one or more COMx (where x is the number of the COM port. i.e COM5) options depending on the number of serial ports available on your computer. The COMx options are typically used for attaching to something like a UNIX computer via serial cable or to a router via its serial console cable. 

To test a specific COM port select that COM port you wish to test. Once the COM port is selected you will not be able to access the other options on this dialog box. They will appear grayed out.

Click OK and select these options:

9600 Bits Per Second, 8 Data Bits, No Parity, 1 Stop Bit, and Hardware Flow Control.

Before clicking OK on the COM3 Properties Dialog Box look at the lower left corner of the HyperTerminal Window. Notice it says "Disconnected" See graphic Below.

Now click the OK button on the COM3 Properties Dialog box. Watch the lower left corner of the HyperTerminal Windows. If the COM port is available and can be opened you will see the status change to Connected. See graphic below.

 If you select OK and get an error saying "Unable to open COMx (where x is the COM port number). Please check your port settings". The COM port you are testing is being used by some device or is not functioning correctly.

Start at the beginning of the COM port test and test another available COM port.

If you receive the error we discussed on every port you select then there are no available ports and you will need to either troubleshoot further or speak to your hardware manufacturer and ask your manufacturer to recommend a hardware solution appropriate for your situations.

Test COM port by using Loopback tester

This is a simple and useful tool for testing RS-232 ports in DTE equipment are working working or not. This plug is connected so that every sent character is echoed back.

 If you Short DB9 (Com Port / RS232) Pin 2 & 3, & Press any Word via Keypad, you can get Eco of that Key. IF you got replied then your Com port is Working Normal, IF not then need to either troubleshoot further or speak to your hardware manufacturer and ask your manufacturer to recommend a hardware solution appropriate for your situations.

Differences between RS-232 and full-duplex RS-485

From a software point of view, full-duplex RS-485 looks very similar to RS-232. With 2 pairs of wires -- a dedicated "transmit" pair and a dedicated "receive" pair (similar to some Ethernet hardware), software can't tell the difference between RS-485 and RS-232.

From a hardware point of view, full-duplex RS-485 has some major advantages over RS-232 -- it can communicate over much longer distances at higher speeds.

Alas, a long 3-conductor cable intended for RS-232 cannot be switched to full-duplex RS-485, which requires 5 conductors.

RS-232 is only defined for point-to-point connections, so you need a separate cable for each sensor connected to a host CPU. RS-485 allows a host CPU to talk to a bunch of sensors all connected to the same cable.

Differences between RS-232 and half-duplex RS-485

But a lot of RS-485 hardware uses only 1 pair of wires (half-duplex). In that case, the major differences are

• Each RS-485 node, including the host CPU, must "turn off the transmitter" when done transmitting a message, to allow other devices their turn using the shared medium
• The RS-485 hardware generally receives on the receiver every byte that was transmitted by every device on the shared medium, including the local transmitter. So software should ignore messages sent by itself.

A long 3-conductor cable intended for RS-232 can often be switched to half-duplex RS-485, allowing communication at higher speeds and at higher external noise levels than the same cable used with RS-232 signaling.

RS-232 is only defined for point-to-point connections, so you need a separate cable for each sensor connected to a host CPU. RS-485 allows a host CPU to talk to a bunch of sensors all connected to the same cable.

Alas, half-duplex RS-485 networks are often more difficult to debug when things go wrong than RS-232 networks, because

• When a "bad message" shows up on the cable, it is more difficult (but not impossible) to figure out which node(s) transmitted that message when you have a shared-medium with a dozen nodes connected to the same single cable, compared to a point-to-point medium with only 2 nodes connected to any particular cable.
• Transmitting data bidirectionally over the same wire(s), rather than unidirectional transmission, requires a turn-around delay. The turn-around delay should be proportional to the baud rate -- too much or too little turn-around delay may cause timing problems that are difficult to debug.

Differences between RS-232 and both kinds of RS-485

RS-485 signal levels are typically 0 to +5 V relative to the signal ground.

RS-232 signal levels are typically -12 V to +12 V relative to the signal ground.

RS-232 uses point-to-point unidirectional signal wires: There are only two devices connected to a RS-232 cable. The TX output of a first device connected to the RX input of a second device, and the TX output of the second device connected to the RX input of the first device. In a RS-232 cable, data always flows in only one direction on any particular wire, from TX to RX.

RS-485 typically uses a linear network with bidirectional signal wires: There are typically many devices along a RS-485 shared cable. The "A" output of each device is connected to the "A" output of every other device. In a RS-485 cable, data typically flows in both directions along any particular wire, sometimes from the "A" of the first device to the "A" of the second device, and at a later time from the "A" of the second device to the "A" of the first device.

Point To Point Communication for IP Camera

Point To Point with Nano Tp-LocoM5

Many Installers are requesting methods to connect their Security Systems. From running cable race ways in commercial buildings to installing conduit above or below ground in residential installations, running wired connections can take a lot of time – which equals more money to spend in labor. This article can serve as a guide on how to maximize the use of our Nano Station Loco M5. In this article we will be going to be utilizing an IP Megapixel system.

Example: IP camera System

Items Needed:-

TP-Loco M5

Any IP camera

Any NVR

Category 5, 5e or 6 Cable / Patch Cables

PoE Switch

Before installing any hardware we first need to configure the Nanos. Lets start by Configuring the Nano that will act as an Access Point. This is the one that will be located at the Main Network.

Nano (Access Point)

Navigate to http://192.168.1.20 on your web browser. If you get this page . Click on “Continue to this website (not recommended)”

This is the correct page you should see displayed on your browser. Once you are here you can log in using UBNT as Username and Password.

Select your Country and agree to the terms of use by ticking the radio button.

Once you have gained access to the Main GUI, navigate to the Wireless Tab

Match the Settings displayed.

Wireless Mode: Access point
WDS : Enabled
SSID: UBNT_Bridge
Security : WPA2-AES
Preshared KEY: UBNT2014

Hit Change but not apply.

Network Mode: Bridge

Static Ip: 192.168.1.159

Match your Gateway as well as the DNS server. In this example we left this out as many networks are different.

Finally hit apply.

Once you have applied the settings your Nano will restart and you can install the Access Point at the Main location where the Main network is.

Nano (Station)

Lets go ahead and open an internet browser.
Navigate to http://192.168.1.20

Use the following credentials to log in.

Username: UBNT Password: UBNT

Select your Country & Language

Check the radio button to Agree the terms of use as.

Once you are loge in navigate to the Network Tab

Use the Following settings

Wireless Mode: Station
WDS : Enabled
SSID: UBNT_Bridge
Security : WPA2-AES
Preshared KEY: UBNT2014

Navigate to Network

Use the Following settings

Network Mode: Bridge

Static Ip: 192.168.1.160

Match your Gateway as well as the DNS server in this example we left this out as many networks are different.

Navigate to the Ubiquity tab

Make sure to match these settings and hit apply.

Once you have completed both Nanos you can install them making sure that they both have line of sight between the devices, some minor adjustments can be done to ensure a good connection.

The Nano’s will lock onto the network by themselves or you can click on the SELECT button this will open up a tab that will display any Access Points in the area select the correct one and lock onto it.

Once you have completed setting up your Point to Point Bridge we can focus on the location.

In this illustration you can see that the Nano (Access Point) is in line of sight with the Nano (Station) that has an IP camera connected to it.

The Connections are simple

Site Side

1.        Connect the camera that you need to add into your Main network onto its own PoE Switch “POE Port”

2.        Attach the “LAN” Cable on the single port PoE switch to the “LAN” on the PoE switch from the Nano (Site)

3.        Attach the “PoE” Cable to the Nano Station “LAN” port.

Main Side

1.        Connect the Nano Station to its PoE switch  (“LAN” to “PoE”)

2. Attach an Ethernet cable from your Router LAN port to the “LAN” port located on the Nano stations PoE switch.

*NVR connections are simple simply attach your NVR to the Router  by attaching a cable in between the LAN port on the NVR to the LAN port of your router.

Mounting Options:

The Nanos come already designed to be attached to a pole, there is a supplied Nylon Zip Ties.

Troubleshooting Tips:

If you have successfully connected all of the devices and you cannot seem to ping your camera on any device on the Station side, make sure that the WDS is enabled in both the AP and Station.

If signal is poor you can use the AirView Application to check your signals. If you are not that tech savvy you can use the Signal bars behind the units or simply log in to both and tweak your nano’s position.

Once you have completed mounting your camera and Nano stations as well as configuring your Nano’s, your system should be up and running.

Also, to view your cameras outside your network, some port forwarding is needed. Ports that need to be opened are 37777,37778 and HTTP ports.

About PSIM

What is PSIM?

PSIM stands for Physical Security Information Management, however it certainly requires further explanation about why it is important. Firstly, the future of all security systems is IP based, this means that CCTV, Access Control, Intruder and Fire Alarms will be computer based. Analogue and standalone systems are becoming more redundant and technology is moving rapidly towards converging all these IP based systems onto a single software management platform.

Assuming your security systems are IP based, then PSIM software packages will make an incredible difference to way you secure your school, business or public sector space. This means facility or building management staff can centralise all systems onto a single platform and remotely manage the building.

The key attributes of a PSIM system are:

1. Collection: Device management independent software collects data from any number of disparate security devices or systems

2. Analysis: The system analyses and correlates the data, events, and alarms, to identify the real situations and their priority

3. Verification: PSIM software presents the relevant situation information in a quick and easily-digestible format for an operator to verify the situation

4. Resolution: The system provides Standard Operating Procedures (SOPs), step-by-step instructions based on best practices and an organisation’s policies, and tools to resolve the situation

5. Reporting: The PSIM software tracks all the information and steps for compliance reporting, training and potentially, in-depth investigative analysis

6. Audit trail: The PSIM also monitors how each operator interacts with the system, tracks any manual changes to security systems and calculates reaction times for each event

PSIM is considered essential for Control Rooms or Command and Control Operations, as the software, provided all the systems are IP based, converge all the disparate systems onto a single platform to provide full management. Common security systems integrated onto a PSIM platform are:

- IP Access control systems

- IP CCTV systems

- Fire detection

- Video wall

- Intrusion detection systems

- Perimeter Intrusion detection systems

- Radar based detections

- GIS mapping systems

- Intercom or IP Phone systems

- Automated barriers & bollards

- Building management systems

The aggregated data, information and footage from the various systems provides the operator with intelligence to effectively manage situations (i.e fires, intruders etc) or day to day management of the building (i.e remote door locking etc). Ultimately, this means the need for large teams of facility staff can be reduce and the building managed centrally by key operators. A key reason for the development of PSIM has been the technology improvements of the systems listed above, which has meant software developers have been able to integrate and converge these systems onto single platforms. Technology in security systems is improving dramatically, prices are falling for systems and the software required to manage them is now available. It really makes sense to move forward and use PSIM to its full potential, let Sunstone help you embrace the future.

iPhone and iPad Security Camera Apps

iPhone and iPad Security Camera Apps

As a well-known eSecurity Professional in India I got many appreciation call/mail for my Blog writing. Thanks to all of you for read and understand my wrong English writing on my blog. Recently I visit Bhubaneswar (Located in India, Capital of Orissa) and face some question, customer ask you people highlight our NVR/ DVR is support Remote viewing on iPhone & iPad, but we are not enjoy the benefits of mobile security camera monitoring. Our System Integrator / Installer technical person come and say something that we are not understands. So you’ve come to the right place. Many IP camera and NVR manufacturers have unveiled top-of-the-line mobile monitoring apps compatible with the iPhone and iPad. A list of manufacturer iPhone security camera apps and iPad security camera apps is provided below, each with a detailed description of noteworthy features.

Optica

iPhone & IPad Security Camera App Name: OpticaMobile & OpticaMobile HD

Optica, a leading manufacturer of high-definition IP cameras, offers OpticaMobile and OpticaMobile HD mobile apps designed for iPhone, iPad, and Android devices. OpticaMobile delivers a wide spectrum of features to improve the viewing experience for all Optica IP cameras, including quad-view mode, live video streams, bookmarking, audio, snapshots, dual stream support, and PTZ control of Optica’s P218Z speed dome. It’s an easy and convenient way to tap into your Optica IP camera system while on the go. OpticaMobile HD is built for use on the iPad, while OpticaMobile is compatible with iPhone and Android devices.

Milestone

iPhone & IPad Security Camera App Name: XProtect Mobile

Milestone is one of the leading providers of video management software. Always on the forefront of IP video technology, Milestone offers an iPhone security camera app designed for use with the iPhone 3GS, iPhone 4, iPhone 4S, iPhone 5, iPhone 6, and iPad. To use the iPhone and iPad app, you must first have Milestone’s free XProtect Mobile Server installed and configured, which you can download from the Milestone website. Once installed on your iPhone, you can view live video from several cameras simultaneously; play back recorded images; control PTZ cameras; connect to cameras from more than one site; and send images to others via MMS and email. It’s by far one of the best mobile monitoring apps out there.

Smartvue

iPhone & IPad Security Camera App Name: Smartvue 9

An all-star player in the NVR market, Smartvue offers a complimentary iPhone and iPad monitoring app compatible with a wide range of IP camera brands and styles such as Axis, Sony, Optica, Vivotek, and Panasonic. This innovative app allows you to view numerous cameras at once, slide through live images, connect to different cameras, change display options, see off-site camera monitors, view recorded video, and search archived footage. It’s easy to use, has an intuitive design, and operates through simple touch screen functions such as scrolling and pinch-to-zoom.

Vivotek

iPhone & IPad Security Camera App Name: Vivotek iViewer

The iViewer iPhone security camera app created by Vivotek is compatible with the iPhone 3GS, iPhone 4, iPhone 5, iPhone 6 and iPad devices. With the iViewer app installed on your iPhone or iPad, you can view your live camera feed anytime, anywhere. You’re not limited to just one camera either; the iViewer supports hundreds of live camera feeds from innumerable server connections. The app gives you complete control of your live video, including PTZ camera control, a snapshot command to capture specific video frames, real-time switching of cameras to change displays as needed, and saving your display settings. The app also features remote playback so you can browse through recorded images for peace of mind. Additionally, you can search recorded video via a date and time, and playback recorded video in time intervals of 1, 2, 5, and 10 minutes.

QNAP

iPhone & IPad Security Camera App Name: VMobile

NVR manufacturer QNAP offers a free mobile monitoring app called VMobile that works with most versions of the iPhone as well as the iPad. Using the VMobile app, you can view your IP cameras and playback recorded video from the VioStor NVR series. Unique to the VMobile app is its ability to connect with hundreds of network cameras of varied brands. You’ll have access to breakthrough mobile monitoring features like PTZ control, notification of events and snapshots, adjustable viewing modes, and recorded video playback.

Everfocus

iPhone & IPad Security Camera App Name: MobileFocus

Everfocus is one of the world’s most trusted manufacturers of CCTV camera systems and DVRs. The MobileFocus app supports multi-touch control for zooming in on images, quick access to preset positions, sequence mode, image snapshots of real-time video, PTZ control, full screen displays, live audio, and device management, among many other convenient features. The app currently works with all Paragon Series DVRs and HD Series DVRs.

Backup and Archiving

Backup and archiving are always mentioned together, as both of these technologies support primary data storage. However, the commonalities end over here and cannot be carried forward. But in enterprise IT world it is often observed that archive is analogous to backup.

Simply put, backup and archive are not the same and here’s why explained in simple terms-

Data Backup

Data backup is intended to recover individual lost or corrupt files, or individually corrupt operating system instances. The backed up data has both active and inactive information which encompasses all of your production data. This backup set is useful for purposes of recovery in case of the original copy of data is lost or becomes inaccessible due to reasons. It is always critical that a backup is a copy of production data and the actual data still resides on the production storage systems.

Backups are historically being optimized for large scale recoveries. They are written in large blocks to dedicated hardware like tape libraries or deduplicated disk backup appliances.

On a typical note, these backups are scheduled, often every 24 hours, sometimes more frequently, even hourly with some continuous data protection solutions. The data driven by a backup is stored on a tape or a disk solution or off site like a cloud platform. Restoration from backup can be a complex and lengthy process depending on the volume of data to be restored.

Data archiving

Data archiving on the other hand, is data meant for long term retention, typically for compliance purposes in regulated industries such as finance and legal sectors. These are actually designed with very different access profiles. These systems typically store individual data objects such as files, databases or email messages and usually also capture metadata associated with each item.  The result is that an archive can provide immediate granular access to stored information and so accessing an individual file or email is typically very easy in an archive system.

Generally, archiving solutions which retain and index all copies and versions of a document, file, or email, making them easily are expected to be rapidly retrievable by end users rather than IT admins.

So, please do not treat your backups as archives or vice versa as same, as they serve for different purposes.

Installation of Camera In Harsh Environment

In this article, our aim to provide you some basic information about same standard which determine the outdoor working reliability. Outdoor Security cameras must be able to continue working properly. To achieve this, the security cameras must can effectively withstand in harsh conditions - such as rain, dust, wind, sand, salt, extreme hot and cold temperature etc. Many factors determine the camera whether they are suitable for specific outdoor critical environments.

1.       WEATHERPROOF STANDARD - INGRESS PROTECTION (IP)

To let user know whether certain products are suitable for certain conditions, some international organizations set standards that can indicate how effectively product can work in environment prone to water, dust, explosion and impact. Ingress protection is the most widely used one standard.

IP stands for ingress protection which is a standard (IEC-529) that specify how caable equipment can withstand the ingress, or entry, of dust or water. An IP is usually consisted of two numerals, the first digital indicates the level of protection that the enclosure provides against access to hazardous parts (e.g. electrical conductors, moving parts) and the ingress of solid foreign objects, the second digital indicates the protection of the equipment inside the enclosure against harmful ingress of water. For harsh environment, the security camera should be rated IP66 to IP68 as opposed to IP32 to IP54 for indoor environment.

2.       IMPACT PROTECTION - IK RATING

IK or impact protection, is the standard that specify degrees of protection provided by enclosures for electrical equipment against external mechanical impacts in accordance with IEC 62262:2002 and IEC 60068-2-75:1997. IK rating system ranges from IK00, or no protection, to IK10, or protection against 20 joules impact, equivalent to impact of 5kg mass dropped from 400 mm above impacted surface. Typically, vandal-proof security cameras utilizes high impact polycarbonate plastic dome. Tamper-resistant screws make the unit resistant to vandalism.

3.       SURGE PROTECTION

The majority of all surge-induced damage is caused by surges and spikes travelling along unprotected video, data, and power lines. These surges originally come from a wide variety of sources, including lightning strikes and static charge buildup. Surge protection can provide protection for both IP video surveillance and analog video surveillance systems which include front-end cameras, data lines, power lines, back-end storage DVR, NVR, as well as PoE switches. When security cameras are installed outdoor, extra surge protection is essential, surge protection is a smart investment in preventing not only equipment loss, but the potential loss of critical information.

4.       EXTREME LOW/HIGH TEMPERATURE

Users also need to consider the temperature factor if the camera is installed in extreme hot or low temperature degrees environment, the security cameras should be able to withstand these conditions. While typical security camera ought to have a working temperature range from -10 to 60 degrees Celsius, critical environment products should be able to work in a range between -40 and 70 degrees Celsius. Some IP cameras has built-in heater and fan to maintain the camera's inner temperature therefore allows camera to work in an extreme high/low environments.

5.       OTHER CUTTING-EDGE TECHNOLOGIES

Many other new technologies which has been implemented into security camera to enable them work in places that subject to danger or extreme weather conditions. Pelco by Scheider Electric released a series of products that have capability to withstand water and dust ingress, fog, high and low temperatures, winds of up to 57 meters per second, explosions, and corrosion by salt and different types of chemicals.

Many different technologies have been utilized to make those features possible. For example, some products feature the pressurized integrated optics cartridge (IOC) technology, which is able to protect the equipment from moisture and airborne contaminants and packages an auto-focus camera, lens, heater, and sensors in a small, self-contained, and sealed unit. Another cutting-edge technology is Dry nitrogen pressurized to 10 pounds per square inch gauge (PSIG), which protects the environment inside the cartridge, whereby sensors strategically placed in the cartridge send an alert message if changes in pressure, humidity, or temperature are beyond factory-set threshold points.

Some security cameras also feature heater, window defroster, sun shroud, and thermal insulation blanket to enable operation in temperature conditions ranging from as low as -46 degrees Celsius to over 49. In case the power failure during an ice store, the entire camera can deice itself and become operational in just two hours after power restore at a temperature as as -25 degrees Celsius.